Sika 554 Haltbarkeitsdatum

Umbau- und Reparaturanleitungen + Erfahrungsberichte
Antworten
camper42
Ganz neu hier
Ganz neu hier
Beiträge: 3
Registriert: 30 Nov 2025 19:49

Sika 554 Haltbarkeitsdatum

#1 

Beitrag von camper42 »

 Themenstarter

Hallo zusammen,
ich habe zwei Kartuschen Sika im Keller gefunden, bei denen vor 2 Jahren das Haltbarkeitsdatum abgelaufen ist.
Kann man die noch verwenden?

Grüße
Jochen
Benutzeravatar
MobilLoewe
Wohnt hier
Wohnt hier
Beiträge: 2919
Registriert: 07 Jun 2022 10:43
Wohnort: Metropole Ruhr

Re: Sika 554 Haltbarkeitsdatum

#2 

Beitrag von MobilLoewe »

Wenn das Zeugs sich noch gut verarbeiten lässt,.dann für weniger wichtige Arbeiten noch verwendbar. Für wichtige Verklebungen würde ich jedoch neue Kartuschen nehmen.

Gruß Bernd
Hymer ML-T 570, 4.1t Sprinter 907 4-Matic, 10,25″ MBUX, 9-G-Tronic, OM654 mit 190 PS, Assistenten fast volle Hütte. Big Toy... :mrgreen:

Davor Hymer B-MCT 600, ML-T 580 V6 4x4 und zwischendurch kurze Zeit GCS 700 4-Matic, Sprinter seit 1999.
Benutzeravatar
Schnafdolin
Wohnt hier
Wohnt hier
Beiträge: 2873
Registriert: 15 Nov 2010 11:57
Wohnort: Nordöstlich von Dresden
Kontaktdaten:

Galerie

Re: Sika 554 Haltbarkeitsdatum

#3 

Beitrag von Schnafdolin »

camper42 hat geschrieben: 14 Jul 2026 21:20
iSika im Keller gefunden,

...wenn der überhaupt noch zu den Überlebenden gehört. Ich würde ihn nicht mehr verwenden.

Martin
● 906 316 4x4, 2016
● ex 2x 903 316+313 4x4
● ex 2x LR Defender 110 TD 5
● ex 3x VW LT 40/45 4x4
. Allrad seit 1985

Bin ich ölich, bin ich fröhlich :D
nadabsardar
Ganz neu hier
Ganz neu hier
Beiträge: 2
Registriert: 07 Sep 2026 14:16
Kontaktdaten:

Re: Sika 554 Haltbarkeitsdatum

#4 

Beitrag von nadabsardar »

camper42 hat geschrieben: 14 Jul 2026 21:20 Hallo zusammen,
ich habe zwei Kartuschen Sika im Keller gefunden, bei denen vor 2 Jahren das Haltbarkeitsdatum abgelaufen ist.
Kann man die noch verwenden?

Grüße
Jochen
Hi Jochen,

Sika sealants (including 554) will usually still be usable a couple of years past the printed expiry date, provided the cartridges have been stored somewhere cool, dry and out of direct sunlight — a basement is generally fine for that.

Worth checking before you commit to using them on anything structural or watertight:

Consistency — squeeze a small amount out first. It should flow smoothly and evenly. If it's gone stringy, grainy, or won't extrude properly, it's had it.
Skinning time — a bead of fresh sealant should start forming a skin within 10–20 minutes (touch it lightly with a gloved finger). If it takes much longer than usual, or stays tacky/wet for hours, the curing agent has likely degraded.
Smell — it should still have that typical sharp, slightly vinegary/acetic smell (for acetic-cure types) or a milder smell for neutral-cure. A "dead" or flat smell can indicate it's no longer reactive.
Full cure test — do a test bead on some scrap material and leave it 24–48 hours. Check it's cured right through (not just skinned on the surface) and still has proper flexibility/adhesion when you try to peel or flex it.

If it passes all of that, it should be fine for general use. That said, for anything critical — roof seams, windscreen-adjacent areas, or places where a failure would let water in — I'd personally not risk two-year-out-of-date sealant and would just buy fresh cartridges. It's cheap insurance compared with the cost of chasing a leak later.

Hope that helps!
Antworten